Todas as mensagens

Q: How long are the two wing M3 screws with plastic knobs?

perguntado por sprite77 sobre 2021-11-25 12:30:47

3DFlyZone 30mm

2021-12-14 11:10:38 Útil (0)
respostas (1)

Q: Can I get somewhere original prop? Or the same one?

perguntado por BG405323211 sobre 2021-08-13 09:44:30

3DFlyZone HQ 9" X 4.5 prop works well, balanced perfectly from factory , light weight and flexible enough to not cause damage when land

2021-12-11 08:43:39 Útil (0)
respostas (2)

Q: This plane has issues and often gut death spiral

perguntado por basetau sobre 2021-10-17 06:28:38

3DFlyZone perhaps learn to fly properly before criticising a good aircraft, or learn to build or set it up better. me and two friends have this aircraft and all fly ok

2021-12-11 08:41:45 Útil (0)
respostas (3)

3DFlyZone increase the height of the rear rudder stabiliser , makes all the difference. where it has been flattened off on the top, add some thin plastic and cover with vinyl tape to secure. very easy to do and makes the aircraft fly great

2021-12-11 08:39:17 Útil (0)
respostas (4)

Q: what is the range of remote

perguntado por BG563942259 sobre 2020-07-24 10:08:42

3DFlyZone had over 12km with mine, using iflight crystal antenna patches and iflight albatros antenna fitted to a wing with dji air unit working as the receiver too

2021-12-04 06:16:51 Útil (0)
respostas (4)

3DFlyZone Defo does need the mods , esp the tail fin , find it hard to believe some here think it flies ok without it.. going to fit the carbon spars inside, prevent my nose snapping off again haha , great review !

RagTheNutsOff 09/09/2020
The LTE Rambler RS itself is not a bad model at all, I've enjoyed flying it a lot so far. It does need some minor modifications however sadly the manufacturer seems to have a few attitude issues. Staying on the positive side the foam is well moulded and I like the look of it. It does fly well with some minor mods (mentioned shortly) and it will take a wide range of batteries very easily as the battery bay is huge, around 8" x 4" big! However you will need to add 40mm of depron foam to the vertical stabiliser to tame the hunting (shown clearly in several YouTube videos), pins in the rear hatch to stop the fin flying off and a clip to the front hatch as the magnets are not very good and definitely use 4mm carbon rods in the nose either to stop it from snapping off too (surprising as the same mistake by the designer who made the Dart XL, which had exactly the SAME issue). The Rambler RS can be a bit of a challange to launch, even with a standard 5200mAh 4S pack. FULL throttle and a hard throw is the key to a good launch. Also create your own or 3D print a nose cover to block up the front nose vent. I did find that when landing in wet grass, water got into the fuse area and soaked the battery and as far back as electronics in the rear. Blocking the nose up will stop this from happening. The manufacturer's attitude towards customer support is a whole different discussion point (less than desirable), however as mentioned at the beginning, not a bad model at all, needs a few, very easy mods to make it a good model that you'll also enjoy too. Matt
Comentários (15)

3DFlyZone works well with DJI . just keep trying and you will get it working

2021-12-03 03:07:58 Útil (0)
respostas (2)

Q: Does KIT version include Servos please

perguntado por 3DFlyZone sobre 2021-11-25 04:13:32

The seller no

2021-11-26 02:53:09 Útil (1)
respostas (1)