Todas as mensagens

Q: Is the party mask included?

perguntado por RichardTardif sobre 2020-01-18 12:04:04

ChristianMoe90 🤣🤣

2020-01-19 12:16:10 Útil (7)
Enviar
respostas (6)

Q: Trim function for fixed wing?

perguntado por Richard sobre 2021-12-30 07:46:38

The seller Does not support fixed wing, only suitable for traversing aircraft

2021-12-31 03:46:46 Útil (0)
Enviar
respostas (1)

jhpmlenders Ithas a head tracker, but you need gimbal setup on your plane or drone to use it with

2021-07-27 11:08:43 Útil (0)
Enviar
respostas (4)

Q: what's different between emax rs2306 motor and this motor (performance)

perguntado por anapya sobre 2021-03-31 12:54:00

BG171716181 Completely different. 2306 is a smaller motor, much lighter. Made for drones but very usable for smaller rc airplanes. This is aimed at rc airplanes as is observed from the x mount and longer shaft. It will accept bigger props with a spinner.

2021-04-16 07:06:01 Útil (1)
Enviar
respostas (1)
Richard 19/08/2019
Considering the price and how quickly it shipped i rate it 5 stars. Its not perfect but.... All the pieces are there, there is enough cf to keep it rigid enough and while there are no instructions, its easy to put together. The only deviation was a thin 4mm balsa leading edge which i sanded down for aerodynamics and looks . I also added a touch of leading edge fixed slats. Otherwise i used a 2212 2200kv a 6045 prop and a light 3s 1300. This setup is light and is a little unstable in the wind. Otherwise it flies great and is capable of nice slow flights and effortless landings. I guesstimated the cg and was a tad tail heavy and adjusted the battery position to correct it. I landed about 20mm from the leading edge extender and main wing junction. Start there and adjust to your liking. Overall very pleased with the overall quality and easy of build. It looks great for a foamboard style build. For me as a Canadian this came out much cheaper than a flitetest kit which is what I wanted to get. It was a faster and better looking build in my opinion. A few things Use a hot glue or tape hinge for the aileron hinges as the PP hinge will fail quickly, do not leave it as is. Make sure that you glue the firewall straight to avoid weird behavior Plan your electronics installation before glueing the bottom plate and figure out how you want to access the battery and electronics. I used a small foamboard insert to give the cockpit shape and a simple bbq squewer and elastic to secure the hatch. You can use magbets or use the bottom to oprn instead Hope this review was helpful.
15
Recomendações
Comentários (0)

Q: What's the BEC the flight controller? Is there a wiring diagram available

perguntado por RichardTardif sobre 2019-03-27 08:18:37

SOLARFPV 5 volt BEC, but the board takes 2 to 4s.

2020-12-13 06:08:11 Útil (0)
Enviar
respostas (1)

Q: Notchy for racing or smooth for freestyle?

perguntado por Richard sobre 2020-09-16 06:42:50

hilite the motors are too weak at 4s. havent tried on 6s but you need a very light build and still will not get a powerful setup.

2020-09-25 07:03:43 Útil (0)
Enviar
respostas (1)

Q: Whats the motor mount pattern?

perguntado por Bambusgott sobre 2020-09-16 05:03:41

BG171716181 16x16

2020-09-16 06:43:04 Útil (1)
Enviar
respostas (1)

Q: Would the other cab like the c12-c24 fit on the frame?

perguntado por RichardTardif sobre 2019-04-24 07:25:13

CantennaB no probably not.

2020-09-09 09:09:25 Útil (0)
Enviar
respostas (2)