Todas as mensagens

Q: I can use In 2838 motor in weltoy A 959 ?

perguntado por Sayedbakhtyar sobre 2021-05-18 07:05:39

Marcus454 It should I used on a 2845 motor 3mm shaft..

2021-06-02 02:15:58 Útil (0)
Enviar
respostas (1)

Q: I can't fix the central axle for this car, can you help me?

perguntado por Santos sobre 2021-05-17 06:00:15

Marcus454 yes absolutely what is the problem with your truck?

2021-05-17 06:58:30 Útil (0)
Enviar
respostas (2)

Q: How many meters is the (shaft) hole diameter of these gears?

perguntado por mehrdad dabirsiaghi sobre 2018-12-18 01:18:14

Marcus454 the big ring gear has a inside diameter of 5mm the little spider gears 1mm I.D the side gears with oval I.D is 5mm x 4mm and the 2 out drive gears have 5mm I.D hope that helps you. .

2021-04-29 05:06:27 Útil (0)
Enviar
respostas (1)

Q: what is the maximum operating voltage for its 2650kv variant?

perguntado por BG413753950 sobre 2021-04-28 12:18:54

Marcus454 I run my 2650kv with a heat sink no fan 120A hobbywing esc 3s and 4s all day with 150mm tires no problem 16 volts. .

2021-04-29 04:48:49 Útil (0)
Enviar
respostas (1)

Q: is the big gear metal?

perguntado por Adamkiller27 sobre 2019-11-15 07:02:22

Marcus454 this is for the axle and yes the ring gear on it is metal. . if your looking for a metal spur gear you need a center differential. this is a front or rear axle differential. .

2021-04-23 01:20:39 Útil (0)
Enviar
respostas (2)

Q: Hello would this diff fits in to a JLB Cheetah?

perguntado por biglong18 sobre 2021-04-13 06:12:36

Marcus454 no absolutely not. . cheetah has slipper clutch not center differential. .

2021-04-23 01:07:25 Útil (0)
Enviar
respostas (1)

Q: hello. what is the width of the gear

perguntado por BG224861717 sobre 2020-02-01 11:12:26

Marcus454 it's 4mm. the exact measurement with my micrometer is 3.8mm..

2021-04-23 01:01:18 Útil (0)
Enviar
respostas (2)

Q: Does M1 pinion fit? can you give upgrade pinion item I'd?

perguntado por irarkh sobre 2020-09-12 03:41:57

Marcus454 yes it's mod 1.. I'm running it with 17 tooth pinion and 150mm tires 2250kv motor 50mph on 4s all day no problem. .

2021-04-23 12:58:27 Útil (0)
Enviar
respostas (2)

Q: can someone tell me the inside bore diameter the end where grub screw goes in

perguntado por davyboy77 sobre 2020-05-18 06:12:36

Marcus454 yes it's 8mm..the grub screw is 5mm..

2021-04-23 12:47:07 Útil (0)
Enviar
respostas (2)

Marcus454 the inside of the shaft is threaded for a 5mm grub screw to secure the pin in the 17mm hub.

2021-04-23 12:36:31 Útil (0)
Enviar
respostas (2)

Q: Can I use this with the FS i6 ?

perguntado por spider sobre 2020-01-16 10:50:44

Marcus454 it's designed to run on AFHDS. . I'm not sure but if you go in your settings and are able to switch between AFHDS & AFHDS 2A you should be able to bind it to your transmitter be aware it only runs 3 channels. A good option would be the fs-bs6 mini so you can use all 6 channels. .

2021-04-21 10:41:37 Útil (0)
Enviar
respostas (1)

Marcus454 there are no setting to turn the beeps off. . I had to disconnect the speakers. there's lipo checkers available on here with no beeper it's basically the same thing just with the display. .

2021-04-21 10:30:30 Útil (0)
Enviar
respostas (2)

Q: what is the dp of the gear so I know what pinion gear to get for the motor?

perguntado por andy1989 sobre 2021-04-01 08:30:20

Marcus454 Hey bro it's mod 1. .

2021-04-07 09:16:08 Útil (0)
Enviar
respostas (1)

Marcus454 it's a mod 1 gear for 1/8 1/10 trucks. . hope that helps you decide. .I run 15 tooth pinion with a 2250 kv motor truck goes 50mph on 4s all day no problem. .

Marcus454 29/07/2020
0
Comentários (2)