Melhores ofertas para Lanterna,Phone Holder - Banggood Brazil Compras on-line

Gravelrash 10/10/2019

Great light. I'm going to compare it to the BLF Q8 Pros:Slighly smaller than the Q8, and the shape is MUCH comfier to hold. Built in USB C charging with included cable means it is easy to recharge on the go, great for camping trips or in the car. Green indicator not as bright (Q8 indicator was a little too bright) Cons: Full brightness/turbo not quite as bright as the Q8. Overall: excellent Build quality, easily a match for the Q8 in that respect. UI great as expected. Tailstands perfectly. I like it a lot.

SOFIRN SP36 BLF Anduril 4x Sumsung LH351D 5650LM Anduril Lanterna Driver Múltipla Operação Super Brilhante 18650 Lanterna

US$78.99 US$81.37

13

Comentários (0)

Gravelrash 16/01/2020

The act of pressing the button to start monitoring Max decibels instantly generates a reading of around 48dB or more, so the Max function is of no use for trying to monitor Max sound levels any lower than 48dB. Apart from that this is OK, and pretty good for the price

LCD Nível de pressão sonora Decibel Medidor de ruído Medidor de medição 30 ~ 130dB

US$20.89 US$22.99

0

Comentários (0)

Gravelrash 16/01/2020

It's OK. I use it to hold a torch.

Universal Suporte Titular de Celular Mesa Cama Braços Longas Flexível Preguiçoso para Samsung Xiaomi

US$15.78 US$18.99

0

Comentários (0)

Kit de impressora 3D DIY TWO TREES® Sappheiros Pro CoreXY com tamanho de impressão de 235 * 235 * 235 mm

US$319.99 US$439.99

Q: Why is there two specs, MAX print size and Print size. Other 235mm cubic and the other 220mm cubic? Which is the correct value for maximum print size that you can actually print with this?

perguntado por tommipaunonen sobre 2019-11-10 02:25:05

Gravelrash The print bed is 235mm x 235mm same as an Ender 3 (the print surfaces are interchangeable). There can be clearance issues around the X/Y axis depending on how you assemble the drive belts and organise your cable management, which can limit the usable area of the XY axis, but I've managed pretty close to the full 235x235 on mine with some forethought and careful routing. I've not measured the full height of the Z axis accurately myself yet, but it is currently set to 235mm in the config file.

2019-11-30 06:59:58 Útil

Enviar

respostas (1)

Gravelrash 30/11/2019

OK, so this item is actually very high build quality, but I've marked it down to 4 stars on quality due to minor QC issues out of the box. The cable for the extruder stepper motor was wired incorrectly, which prevented the extruder from working at all until I had rewired it correctly. The wires for X-axis endstop switch have broken off with only gentle handling and are currently waiting for me to re-solder back in place - would have been preventable with better soldering and/or strain relief. The tensioner for the extruder has a spring that is too long for the tension bolt (or the bolt is too short for the spring) which resulted in the spring pinging off never to be seen again while I was trying to work out why the extruder wasn't working initially. There are also some minor niggles with the firmware setup, and there are known issues with unreliable Z axis homing (easy fix with a 3d printed cap). I also identified and prevented other potential minor issues during assembly thanks to watching some helpful youtube videos prior to assembly. That all said, the printer is of excellent quality, fast, quiet, and has real potential at a bargain price. Just don't buy if you aren't prepared to troubleshoot, tweak and work on it a little bit.