Herby
Q: Is there a way to zero the dc amps? Mine reads about + 0.6 amps with no load. Thank you Herby
perguntado por Herby sobre 2020-01-02 09:19:25
Q: boa noite, ele mede na garra mAh DC e AC? consegue medir 20mAh AC e DC (na Garra miliampéres)
perguntado por Nardi83 sobre 2021-09-18 04:45:46
Herby Try it. You wont hurt it. It will maybe have a low scale like 2 amps which is 2000ma. Herby
2021-09-19 12:58:31 Útil (0)
Selfhem 4g
2019-12-16 03:54:07 Útil (1)Q: does this fit the parkside 12v cordless multi tool
perguntado por BG141372513 sobre 2021-03-27 06:56:43
Herby Measure the hole in your multi tool. It must be 4.3mm.
2021-03-27 03:20:24 Útil (0)Q: why is not clear that the kit doesn't come with a motor or speed controller.
perguntado por BG223754916 sobre 2021-02-19 10:23:56
Herby The end purpose will dictate what equipment is required. Personally I would build this as light as possible and fly it as a powered slope soarer.. I would thermal it with actual live birds. I have actually flown in thermals with a real bald eagle over my house! The eagle is always in command.
2021-02-19 12:41:41 Útil (0)
Herby The description says NO Braking.
2021-02-11 01:28:26 Útil (0)
Q: OK... Going out on a limb here... Is there a listing for the other rotation of these props ?
perguntado por Dropbear sobre 2021-01-31 04:26:47
Herby Direct drive props are for nose mounted motors on airplanes which use ccw rotation. To get the cw props you have to buy cw and ccw props in pairs for drones.
2021-01-31 05:02:33 Útil (0)Q: where to buy extra rubber band ? and price of extra rubber band ?
perguntado por gdsu sobre 2019-08-06 09:50:51
Herby You can loop together gum rubber bands and use several loops together. Use a silicone spray or grease to lube the rubber motors.which prevents chafing.See ebay for tan II rubber strip.
2021-01-21 04:22:01 Útil (1)
Herby Test the mos fets for shorts and function. Check for a signal on the gate If one is shorted, remove that one. Look at youtube for testing fets.It is simple to do.
2021-01-14 01:31:54 Útil (0)
Herby According to the instructions you only need external power if the voltage input is less than 7.8 volts dc. A 12 volt boat would be ok..
2020-12-16 06:08:12 Útil (0)Q: why did my mini spot welder come with a 25V 2200uF capacitor ? it shows 16V on the picture
perguntado por Lou sobre 2020-12-09 12:51:35
Herby 25V will be fine. Not to worry.
2020-12-09 04:41:38 Útil (0)Q: would this be good to install an arc car a plane instead of just guessing how much time I have left?
perguntado por wizkidone sobre 2020-11-20 03:02:36
Herby I do not understand the question...Sorry
2020-11-20 05:26:45 Útil (0)Q: Can it be used for an F550 drone with old pixhawk?(maybe inverted flyable)
perguntado por SmileOnion sobre 2020-11-06 04:23:46
Herby Sorry, not familiar with your hardware,
2020-11-07 08:53:09 Útil (0)Q: The props are both for ccw rotation. The diameter is 52mm or about 2". These are very nice props!
perguntado por Herby sobre 2020-10-18 11:35:22
Malox Non. La paire d'hélice livrée comprend 1 hélice CW et 1 hélice CCW (voir photos des commentaires). Par contre elles ne mesurent pas 75mm comme l'indique le site, elles font 52,3mm de diamètre. Le trou d'axe est suppérieur à 0,8mm donc non adapté à un axe moteur de 0,8mm, elles sont faites pour un axe moteur de 1,0mm pour un montage serré. No. The supplied pair of propellers includes 1 CW propeller and 1 CCW propeller (see photos of comments). On the other hand, they do not measure 75mm as the site indicates, they are 52.3mm in diameter. The axle hole is greater than 0.8mm so not suitable for a 0.8mm motor axle, they are made for a 1.0mm motor axle for tight fitting.
2020-11-06 02:07:05 Útil (1)Q: how many pins does the connector have
perguntado por BG172022114 sobre 2020-10-28 02:54:50
Herby 2 pins
2020-10-28 04:34:38 Útil (0)Sinceramente, o convidamos a se inscrever para receber o e-mail de resposta ao convite!
Se você se inscrever, nós o convidaremos por e-mail para responder a perguntas que as pessoas tenham sobre os produtos. Ao se inscrever, você] também ganhará o "Emblema de útil "! Você pode cancelar a assinatura a qualquer momento na página de configurações de privacidade.
Ajude os outros e seja mais feliz!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
svilponis Press REL button to zero DC amps reading before you start to measure. This should remove any constant offset, for following measurement.This multimeter is not meant for non contact measurement of very low currents, so do not expect, that you can get precise results for currents below 1 A.
2020-01-16 09:23:22 Útil (5)