Todas as mensagens

Q: Dose it work with a 40ch video transmitter?

perguntado por BG524333263 sobre 2021-03-16 08:18:28

nmw01223 It works with any 5.8ghz analogue video transmitter.

2021-03-17 12:18:31 Útil (1)
Enviar
respostas (2)

nmw01223 I use a Foxeer pagoda and triple-feed patch (both SMA male, right handed), seems OK.

2020-12-09 03:19:21 Útil (0)
Enviar
respostas (4)

Q: can i connect this to eachine tx*****ch fpv camera???

perguntado por BG431140211 sobre 2020-09-30 10:01:54

nmw01223 It should work fine with any camera transmitting the standard analogue signal in the 5.8Ghz band, NTSC or PAL. Not familiar with that specific camera, but if it is a standard FPV camera - then yes.

2020-09-30 11:32:22 Útil (0)
Enviar
respostas (4)

Q: is this better than the irange irx4 one? and does it come with the latest updates?

perguntado por BG163940181 sobre 2020-09-20 04:06:14

nmw01223 It basically has the same functionality in terms of protocols supported - that is determined by the software level. Mine did not come with latest updates, the first thing I had to do was update it.

2020-09-21 02:04:56 Útil (0)
Enviar
respostas (3)

Q: is this recommended guard for a *****kv 3" prop?

perguntado por BG102522443 sobre 2020-06-15 01:20:16

nmw01223 Works for me on a 1306 3" prop.

2020-06-15 11:05:46 Útil (0)
Enviar
respostas (1)

Q: will this fit 11xx motors with 3in props ? thx

perguntado por Danaperez sobre 2020-06-08 08:46:51

nmw01223 Since an 11xx motor is not very tall, the props may not clear the guard.With a 1306 (15mm tall) the clearance is ~2-5mm. An 11xx is also a bit small for a 3" prop?

2020-06-08 03:29:35 Útil (0)
Enviar
respostas (1)

Q: Is this good for R.C. Boats?

perguntado por BG084781557 sobre 2020-05-19 02:53:22

nmw01223 I would guess that unless geared down a lot, much too high RPM, much too low torque.

2020-05-19 11:37:35 Útil (0)
Enviar
respostas (1)

Q: how to be procedure to switch PAL / Ntsc ???

perguntado por m.capasso.77@gmail.c sobre 2019-10-10 07:38:38

nmw01223 Re answer from Ambrisial 5/11/19: Are you sure about that? I think the Betaflight OSD setting is to tell it what to expect from the camera, not to set it. Someone else said there is a button on the camera for this. Does not appear to be the case. I can find no way of setting this. The three connections are simply V , V- and video out.

2020-01-03 10:58:30 Útil (0)
Enviar
respostas (3)

Q: Can anyone suggest a transmitter that is compatible with windows 10 and iphone?

perguntado por Mustafa Buğra Güz sobre 2018-02-06 07:38:27

nmw01223 Ifyou mean VTx to transmit to the ROTG02, any 5.8GHz analogue video transmitter. If you mean can this be connected to W10, the answer is yes like any webcam, though I cannot recall the name of the app I used to view it.

2020-01-03 10:10:10 Útil (0)
Enviar
respostas (2)

Q: What are the dimensions of the frame and propeller screws?

perguntado por mhmtsylr sobre 2019-04-28 01:26:33

nmw01223 frame- Standard M2 screws, 4 equi-spaced on a 12mm circle. Propeller - same but 5mm circle.

2020-01-03 10:07:54 Útil (0)
Enviar
respostas (1)