Todas as mensagens

Q: Can display be turned off ? Thanks.

perguntado por oz_pekeren sobre 2021-05-19 09:35:12

JOZE No, the display cannot be turned off.

2021-05-21 02:02:12 Útil (1)
Enviar
respostas (4)

Q: How much warm can it handle (C°) ?

perguntado por oz_pekeren sobre 2020-07-08 03:22:17

whyyo have pumped 40c (100+f) with it no problems

2022-08-10 08:19:54 Útil (0)
Enviar
respostas (1)

Q: What does it mean with 50A current shunt? Can it measure max.50 Ampere?

perguntado por oz_pekeren sobre 2020-07-15 08:14:11

HardWarrior I believe it can only measure up to 50A with the 50A shunt attached. You select the shunt you are using in the testers UI. There is a version that comes with a 300A shunt. Same unit heavier shunt, but it appears to be unavailable from BG right now.

2022-04-24 05:36:44 Útil (0)
Enviar
respostas (3)

BG551754615 Let's say 210-240V AC should this device handle without problems. Can't tell if it works with 110V as well. Be aware: motors on the output side will loose lots of torque in lower speed

2020-06-29 10:36:15 Útil (1)
Enviar
respostas (2)

Q: What is the max. input Ampere that can be sorted out?

perguntado por oz_pekeren sobre 2020-07-14 10:38:39

BG521044824 10Amps

2021-12-10 07:44:33 Útil (0)
Enviar
respostas (2)

BG343834161 The outputs should be separated with diodes with appropriate parameters for the consumed current and voltage. If you do not know what it is (which results from your question), do not know how to do it, do not know how to calculate the current-voltage parameters and choose the right parameters of the elements based on them, then do not do it. You can not only damage the converters, but also cause a fire. In order to give you a solution and to be able to do it safely, you would have to write a lot, a lot, which is a novel and ... teach you a lot. Learn some theory about electricity, voltage and current, power and heat generation by current flow, almost Oma, etc. And have the inverters connected evenly to a professional.

2021-10-26 08:06:24 Útil (0)
Enviar
respostas (1)

RodJosol After connecting the source power supply, the ISDT will start to power up. Then, you will have to plug your desired battery connector (Xt60) to the output side of ISDT also the balance cable. The charger automatically detects what type of battery it is. Also, it will set the default or recommended settings (voltage) but still it is up the user what will be the seeings (voltage and current) prior to start charging discharging storage etc. .

2020-12-21 01:56:16 Útil (1)
Enviar
respostas (4)

Arnror The manual is worthless. No data, no explanations. It's like they don't want to sell it.

2021-10-05 11:55:50 Útil (0)
Enviar
respostas (2)

Q: What is the max. output voltage for battery charging? Is it adjustable?

perguntado por oz_pekeren sobre 2020-07-04 08:31:46

Arnror Yes, it's adjustable. Any supluss amps will be directed to the resistance element(heater)

2021-10-05 11:45:51 Útil (0)
Enviar
respostas (2)

oz_pekeren Cause your cutter is too much inductive and especially a "non regulated" device that this inverter can`t handle with it.. Every load is different and have to be considered by his own specs. 6000 Watt is of course a joke !! Take the half of this number as its peak power first !! For a 1000W cutter you would need an inverter of 2500 W -a quality product- as continuous output power. Or a simple product of -may be- 4000 W continuous power.. That kind of quality product is rare at this seller.

2021-09-13 10:23:40 Útil (0)
Enviar
respostas (3)