Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (16)
  • Imagem (0)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(16)
    • Estrela(13)
    • Estrela(2)
    • Estrela(0)
    • Estrela(1)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 02/06/2021

    A faixa é feita de uma borracha muito macia. A portadora parece resistente. Há limitadores que impedem a trilha de girar. Parece que vou precisar fazer modificações para que ele se encaixe. Não sei se vão trabalhar bem e aguentar. O tempo dirá.

    Mostrar original
  • VIP3

    1. One of the 3D printed rear ear's broke off when I tried to install it. OK, checked the to see if there would be a clearances issue, if I super glued both of them on. No problem.... 2. Installed the front 3D parts, along with the front & back tracks. Releativly no problems. When I tried to test it, just made a bunch of noise. From the nylon axle hubs, just spinning inside the track hubs. I used Masking tape to wrap around the axle hubs. However, I have to remove it, to use the wheels.

    Mostrar original
  • 10/09/2018

    These wheels worked for my wpl truck. 3d printed parts are not the best quality. Some of the holes were too big for the screws because of print quality. Came with all the hardware needed to install even screws. Overall good product. Would like to have 3d print files to reprint items that were not so great.

    Mostrar original
  • 16/01/2019

    With the 3d printed axle /hub fittings supplied,you can easily switch from ordinary 4X4 to All terrain tracks-pop them into the load tray when running on wheels.Fairly sturdy units - I thought hey might throw the tracks when running but I have not had any problems there.A more powerfol motor would be good though as it is sometimes a bit of a struggle to move.At least double the fun factor!

    Mostrar original
  • 05/01/2019

    The idea is good, but there is one drawback. Plastic rubs against plastic and creates additional friction, which is very bad for drives (in my case wpl millitary track 1:16). Plastic drive can not stand, the motor is heated. Now, if we thought out and made a cat through plastic sleeves, or it would be better through bearings, it would be an ideal option.

    Comentários (1)
    Mostrar original
  • 23/10/2018

    Для замены обычных колес машинки WPL и повышения проходимости. Требует замены стокового мотора на более мощный

    Mostrar original
  • 07/09/2018

    para mi wpl b1 y c24

    Mostrar original
  • 30/07/2020


    Mostrar original
  • 27/06/2020

    Parece bom. Ainda não tentei

    Mostrar original
  • 13/05/2019

    passen leider nicht auf Q61.

    Mostrar original

    Total 0 Páginas

    Vá para página


    Você pode estar interessado em

    recommendation for you
    • R$107,51
    • R$53,67
    • R$112,17
    • R$77,55
    • R$411,84
    • R$83,52
    • R$120,17
    • R$155,15
    • R$149,18
    • R$89,48
    • R$18,92
    • R$34,50
    • R$358,12
    • R$143,21
    • R$37,67
    • R$549,15
    • R$1.187,96
    • R$393,94