Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (264)
  • Imagem (25)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(264)
    • Estrela(240)
    • Estrela(21)
    • Estrela(3)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 15/08/2019

    Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

    Comentários (1)
    Mostrar original
  • 18/07/2018

    The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

    Comentários
    Mostrar original
  • 09/10/2018

    not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

    Comentários
    Mostrar original
  • 02/10/2020

    Produto excelente e muito bem acabado.

    Comentários
    Mostrar original
  • 25/09/2019

    good price, good quality

    Comentários
    Mostrar original
  • 02/09/2019

    Seems good.

    Comentários
    Mostrar original
  • 03/07/2019

    These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

    Comentários
    Mostrar original
  • 23/11/2018

    tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

    Comentários
    Mostrar original
  • 25/04/2021

    excelente, mas cuidadoso que funciona com pelo menos 4,5v e não 3,3v. Como ele monta o ne555 integrado que requer pelo menos 4,5v

    Comentários
    Mostrar original
  • 16/07/2019

    Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$9.28
    • US$23.99
    • US$5.99
    • US$4.99
    • US$5.21
    • US$10.99
    • US$2.99
    • US$9.49
    • US$8.99
    • US$12.43
    • US$6.69
    • US$13.81
    • US$11.99
    • US$6.99
    • US$8.99
    • US$19.99
    • US$4.99
    • US$7.99