Opiniões dos clientes

4.77 de 5
Escrever uma crítica
  • Todos Comentários (39)
  • Imagem (5)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(39)
    • Estrela(32)
    • Estrela(6)
    • Estrela(0)
    • Estrela(1)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
  • 2020-05-28 20:15:11

    Bonjour, Pour commencer, l'article livré pourra avoir une apparence différente comme tel a été le cas pour le mien mais cela n'influe en rien sa qualité (Voir photo). L'accroche magnétique est excellente et ne diminue pas vraiment malgré une chauffe intensive du plateau (100°C pour l'ABS). Aucun soucis pour décoller un print quelques minutes après qu'il soit terminé. Restera à voir la durée de vie de la surface lors d'une utilisation relativement soutenue. L'installation prend quelques

    Comentários
  • Tukamen
    NO
    2020-01-10 04:06:25

    is small for cr10s pro

    Comentários
  • Nuno
    FR
    2019-05-04 13:05:32

    Description says usable up to 80°, but in facts, only up to 70° like you could see on the pic. Can't be used for nylon or abs.

    Comentários
  • lex1982
    DE
    2019-03-29 05:01:26

    für 20x20 super aber nicht für 30x30

    Comentários
  • 2019-03-25 14:37:52

    Why would you ship it in a bag with my pulleys and bearings?? There is a large dent in the middle of the surface from being squished into the pulleys. Then the edges have large dents, not to mention one side being folded over. I dont think I'll even use this now as my prints which always start in the center are not going to be flat. I am sure I would have given 5 stars had this been protected some what during shipping.

    Comentários
  • 2020-02-13 15:03:55

    smels like hot plastic at 80C. Also hard to remove petg from it at this temp. Works good for 60C, light smell, so far not bothering me. Meted a bit when I homed the printer and kept nozzle close to bed for about 2 min.

    Comentários
  • StigN
    NO
    2020-09-22 14:49:12

    Great functionality, however it was a little shorter than expected. does not fill the bed of CR10 S Pro V2.

    Comentários
  • 2020-06-12 16:56:04

    this time the flexible is delivered in flat package no folding problem

    Comentários
  • 2020-10-19 05:50:30

    Prodotto valido come da foto

    Comentários
  • sefran
    FR
    2020-09-06 13:04:05

    Pour mettre sur mon alfawise U20

    Comentários
Show:

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • R$7,77
    • R$13,80
    • R$255,52
    • R$42,12
    • R$8,01
    • R$66,22
    • R$119,06
    • R$126,47
    • R$248,77
    • R$511,83
    • R$125,92
    • R$15,60
    • R$131,53
    • R$118,15
    • R$43,50
    • R$86,88
    • R$90,32
    • R$60,19