Comentários de TB67S109AFTG 32 Segmentos 4A Controlador de motor de passo bifásico de 57/86 para impressora 3D - Banggood Brasil Online Shopping

new ok 9 new ok 9 Comentários de TB67S109AFTG 32 Segmentos 4A Controlador de motor de passo bifásico de 57/86 para impressora 3D - Banggood Brasil Online Shopping

:

Download the

Banggood App

Baixe o aplicativo para obter

US$ 3 cupom de desconto

Frete para:

Idioma:

Moeda:

Olá Entrar Participe
Entrar Junte-se a nós
Cliente novo? Começa aqui.
0

TB67S109AFTG 32 Segmentos 4A Controlador de motor de passo bifásico de 57/86 para impressora 3D

US$11.85
~~US$18.58~~
Compre agora

Opiniões dos clientes

4.81 de 5

Ver todos 227 comentários

5 estrela
203 (89.4%)
4 estrela
15 (6.6%)
3 estrela
3 (1.3%)
2 estrela
1 (0.4%)
1 estrela
5 (2.2%)

Escrever uma crítica Obtenha o dobro de pontos de comentário,se você é um dos primeiros 3 comentários publicados!

Todos Comentários (227)
Imagem (24)
Vídeo (2)
Todas as estrelas
- Todas as estrelas(227)
- Estrela(203)
- Estrela(15)
- Estrela(3)
- Estrela(1)
- Estrela(5)

Ordenar por:

Comentários Anteriores

Comentários Anteriores
Mais úteis
Mais Recente

Comentários apenas do seu país (Brazil)

|

Mostrar original

Uma parte da revisão foi traduzida automaticamente.

schuimpgeVIP1
TH
30/08/2016

Although it is a nice and low-priced driver, it is far from a quality TB6600 driver. Opened it up and the IC is a TB67S109AFTG. It's quite capable, operating voltage for the IC is maxed at 50v, so the advised 40v Max Power Supply is reasonable if there's any voltage spikes from the motor under braking. Solder work and cooling of the IC is low quality, you're advised to open it up and check the heatsink connection. Best I think is to replace the heatsink with a bigger one if possible. Tried it on NEMA 23 motor with Z-axis I just finished, works nicely but with no load it got hot very very fast. (Admitted, that's with outside 35'C temperatures as I'm in Thailand.) Overall, for the price, its a really good driver to start in the world of 3d Printing and CNC, but expect it to not last too long if you're moving big loads with it.

Although it is a nice and low-priced driver, it is far from a quality TB6600 driver. Opened it up and the IC is a TB67S109AFTG. It's quite capable, operating voltage for the IC is maxed at 50v, so the advised 40v Max Power Supply is reasonable if there's any voltage spikes from the motor under braking. Solder work and cooling of the IC is low quality, you're advised to open it up and check the heatsink connection. Best I think is to replace the heatsink with a bigger one if possible. Tried it on NEMA 23 motor with Z-axis I just finished, works nicely but with no load it got hot very very fast. (Admitted, that's with outside 35'C temperatures as I'm in Thailand.) Overall, for the price, its a really good driver to start in the world of 3d Printing and CNC, but expect it to not last too long if you're moving big loads with it.

Although it is a nice and low-priced driver, it is far from a quality TB6600 driver. Opened it up and the IC is a TB67S109AFTG. It's quite capable, operating voltage for the IC is maxed at 50v, so the advised 40v Max Power Supply is reasonable if there's any voltage spikes from the motor under braking. Solder work and cooling of the IC is low quality, you're advised to open it up and check the heatsink connection. Best I think is to replace the heatsink with a bigger one if possible. Tried it on NEMA 23 motor with Z-axis I just finished, works nicely but with no load it got hot very very fast. (Admitted, that's with outside 35'C temperatures as I'm in Thailand.) Overall, for the price, its a really good driver to start in the world of 3d Printing and CNC, but expect it to not last too long if you're moving big loads with it.
9

Comentários

Mostrar original
MrFlachiVIP1
AT
13/12/2017

Habe die Treiber montiert und getestet mit Nema 23 180ncm Motoren nach kurzer Zeit (~10-15min) blieb die erste Achse wegen Übertemperatur stehen. Chip ist mit WL Paste und Stücke Alu Blech montiert zwischen Gehäuse (Kühlrippen) und Alu Blech ist keine WL Paste sehr schlechte wärme Abgabe. Nach Reinigen und ordentlicher Wärme abfuhr liefen die Achsen länger (30-45min) aber noch nicht Dauerhaft. Jetzt mit aktiv Kühlung 12V PC Lüfter Ø90mm fahren sie Problem los.

Habe die Treiber montiert und getestet mit Nema 23 180ncm Motoren nach kurzer Zeit (~10-15min) blieb die erste Achse wegen Übertemperatur stehen. Chip ist mit WL Paste und Stücke Alu Blech montiert zwischen Gehäuse (Kühlrippen) und Alu Blech ist keine WL Paste sehr schlechte wärme Abgabe. Nach Reinigen und ordentlicher Wärme abfuhr liefen die Achsen länger (30-45min) aber noch nicht Dauerhaft. Jetzt mit aktiv Kühlung 12V PC Lüfter Ø90mm fahren sie Problem los.

Habe die Treiber montiert und getestet mit Nema 23 180ncm Motoren nach kurzer Zeit (~10-15min) blieb die erste Achse wegen Übertemperatur stehen. Chip ist mit WL Paste und Stücke Alu Blech montiert zwischen Gehäuse (Kühlrippen) und Alu Blech ist keine WL Paste sehr schlechte wärme Abgabe. Nach Reinigen und ordentlicher Wärme abfuhr liefen die Achsen länger (30-45min) aber noch nicht Dauerhaft. Jetzt mit aktiv Kühlung 12V PC Lüfter Ø90mm fahren sie Problem los.
3

Comentários

Mostrar original

Show:

Total 0 Páginas

Vá para página

Vai

Você pode estar interessado em

recommendation for you