Opiniões dos clientes

4.94 de 5
Escrever uma crítica
  • Todos Comentários (32)
  • Imagem (3)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(32)
    • Estrela(30)
    • Estrela(2)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
  • 2020-05-25 11:12:55

    Použito jako spínač indukčního ohřevu 2,5kW

    Comentários
  • tyutje
    NL
    2017-01-26 01:41:58

    I wouldn't put 100 amps on it, but for general use, it is totally fine! It surprised me that it actually came with a top cover to cover up the terminals.

    Comentários
  • 2018-03-06 09:42:33

    Very good solid state relay

    Comentários
  • Niel
    ZA
    2020-08-31 05:57:52

    Product looks good. quick delivery to

    Comentários
  • 2020-03-10 06:39:18

    costlier. in market same product is available at half price.

    Comentários
  • igi0815
    DE
    2017-01-13 18:02:51

    Hallo getestet am Heizbett eines Prusa i3 (anet a8) Pin1 an - Pin2 auf das Heizbett von da an + (das Relais schaltet nach -) 16V / 12A (mehr bringt mein Labornetzteil nicht) und angesteuert mit 12V (5 reichen aber auch) das SSR wird kaum fühlbar warm - quasi nix Spannungsabfall ca. 100mV am Relais = 0.0083 Ohm - sehr gut (mein selbstgebauter SevenSwitch hat 0.003 aber kein so schönes Gehäuse) (bei amazon D gibts nur billige Clone die nichts taugen) Das hier ist einwandfrei ! ------------------------------ Hello this

    Comentários (2)
  • Hansa
    NZ
    2017-06-11 18:21:07

    For me these are wonderful units. I was getting them locally at around four times the price before. But now I'm putting them all over the place. I run a house of alternative electricity with a wind turbine and solar PV panels at 24 volts. These relays are switching hot water elements when the battery charging is full and operating water pumps when needed. Great units. I have four so far.

    Comentários
  • Docus
    DE
    2017-05-09 09:26:05

    This works like a charm. At 3.3V the relay is switching like intended, and it keeps the relay open back to ~2V if the voltage drops. So nice for Arduino projects. Make sure that you power up your Arduino with 5V, because you need the resulting 3.3V at the digital output. I will buy this item again for future projects. Thx

    Comentários
  • 2016-11-16 06:18:12

    Using this on a 3D printer to heat a bed oversized for a standard RAMPS board. Works perfectly well and allows PID control of the heated bed from Marlin firmware.

    Comentários
  • Kegg
    US
    2016-07-14 15:05:52

    Arrived quickly, as depicted, new condition. This is the first time I purchased a solid state relay. It is amazing ! Totally silent, instant, and has an LED indicator. Thank you banggood.com

    Comentários
Show:

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • R$172,76
    • R$176,29
    • R$99,87
    • R$23,45
    • R$182,16
    • R$240,95
    • R$123,74
    • R$96,40
    • R$349,34
    • R$150,54
    • R$22,22
    • R$126,32
    • R$93,99
    • R$279,74
    • R$95,05
    • R$26,98
    • R$122,79
    • R$21,04