Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (100)
  • Imagem (8)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(100)
    • Estrela(90)
    • Estrela(9)
    • Estrela(1)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 16/01/2019

    This combo board has a 4 channel receiver for a motor, rudder, elevator and aileron. There are 6 outputs. Brushed motor solder pads. Brushless ESC solder pads. 2 servos (rudder and elevator). 2 connectors for the opposing ailerons. The receiver auto binds after 10 seconds. Setup a new model with FrSky D8 on the TX and set to bind. Then power the receiver. Wait for steady light, then power off. No mention current ratings. The speed control was able to handle a 0720 17000KV core-less motor. The largest LiPo battery tested was a 3.7V 250 mAh 35C. Alternately, a 1S brushless motor and a tiny ESC can be used. The onboard linear servos are relatively quick and pull 35g. The control horn, pushrod and servo should extend along a straight line. That way the push rod transfers the most movement (7mm) and results in enough control surface sweep. 2 tiny (1m) onboard JST connectors replaces an aileron wiring harness that wires a pair of micro linear servos to operate oppositely (which rolls the aircraft). Adding a pair of digital servos will cost about $20. There is no telemetry but the plane will drop if the signal is lost. The receiver doesn’t appear to have a low voltage cutoff so setting a timer is a good idea. Initially, the receiver seems a little jittery with nothing connected. After setting up the model, it calmed down considerably. Configuring the receiver is a function of a programmable transmitter. I’ve been using the TaranisQ X7.

    Comentários (4)
    Mostrar original
  • 05/06/2019

    Good piece of electronics. Flying well in my small flying wing. Sometime it produce a little louder sound and electronics heat. If you do not move with servo, electronics overheat and stop working. A drop of "contact cleaner" almost eliminate such states.

    Comentários (2)
    Mostrar original
  • 08/07/2019

    Nice little Frsky receiver with x2 servos two servo ports and builtin brushed esc 👌✌️ used it in the balsa 400mm cub 😊

    Mostrar original
  • 18/05/2019

    Connects and and work well with my jumper T12. I fail connecting a servor with mini jst connector. It would handy to know what servor connector is the adequate one.

    Mostrar original
  • 05/07/2019


    Mostrar original
  • 11/04/2019

    Verpackung ok könnte besser geschützt sein Artikel aber super

    Mostrar original
  • 14/03/2019

    Super Receiver for Micro Planes wird 1S and DSMx I put it in the BlackFlyer V2.

    Mostrar original
  • 12/07/2019

    Great little 4in1 👍 servos are slightly stuttering but seems goos

    Mostrar original
  • 29/03/2021

    I bought the dsm2/dsmx version. I had no problem binding it with my Spektrum 2.4GHz Module- equipped Futaba 8 channel heli transmitter. Prior to binding, the servos emitted a constant high-pitched electronic sound, however it disappeared when the bind was established. I have seen comments about these having some chatter at rest but this unit seems pretty good in that respect. As with anything this small, soldering wires to this tiny board will provide a real test of you equipment and skills. The solder pads are so small! The two linear servos on this board respond to the elevator and rudder (not aileron) channels of your transmitter. The two plugs on the board are for aileron and aux channel (such as flaps) as supplied, but can be changed to aileron and reverse aileron by jumping a connection on the back side of the circuit board. It's not a reflection on the product itself, but the packing was not adequate- a thin one-layer mylar pouch inside an unpadded small plastic bag. This item is too delicate to be treated in this manner. It is a testament to the services that transported this item that it arrived in functioning condition. Come on, BG! I'll gladly pay a bit more if it comes in a nice little box next time!

    Mostrar original
  • 17/07/2021

    Quando a voltagem da bateria for inferior a 3,8v, a ligação é liberada e o sinal é sem controle (LED piscando). Naquele momento, apenas o motor continuará girando cerca de 20-30%. O servo não se move. Há alguma melhoria na configuração do receptor? Por favor, diga-me como fazê-lo, se houver um.

    Mostrar original

    Total 0 Páginas

    Vá para página


    Você pode estar interessado em

    recommendation for you
    • R$157,64
    • R$169,32
    • R$75,87
    • R$151,80
    • R$175,16
    • R$46,67
    • R$87,55
    • R$93,39
    • R$379,58
    • R$110,91
    • R$181,00
    • R$145,96
    • R$151,80
    • R$210,20
    • R$3.212,30
    • R$58,35
    • R$391,26
    • R$34,99