Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (105)
  • Imagem (20)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(105)
    • Estrela(102)
    • Estrela(2)
    • Estrela(0)
    • Estrela(0)
    • Estrela(1)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 03/11/2020

    Produto ainda não testado. Observe que a tomada da bateria não é soldada nem entregue e as tomadas do servidor são do tipo JST 1,00mm. É possível observar que os componentes das superfícies soldadas na placa não coincidem com as fotos no site da web. Creio que esta é uma versão atualizada e o receptor suporta os protocolos "AFHDS" e "AFHDS 2A" (ver comentários e perguntas).

    Mostrar original
  • 05/11/2020

    é muito bom produto, eu recomendo

    Mostrar original
  • 13/03/2021

    Obrigado pela entrega rápida.

    Mostrar original
  • 17/12/2020


    Mostrar original
  • 25/09/2018

    Perfect for the small balsa rc models sold here on Banggood. I have used in LX17, Fokker EIII so far. Flying radio range is great. I am still in control when I can barely see plane in distance.

    Mostrar original
  • 14/09/2017

    This receiver is nice and very small but comes without documentation. It is very similar to the "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" Product ID: 1072251 and the "Mini Futaba SFHSS Compatible 8CH Receiver PPM Output With 1mm JST Socket For DIY Micro Quadcopter" Product ID: 1083120 and you can get some more information by digging into the descriptions of these receivers. It binds with my Turnigy 9X / Flysky TH9X but the process takes some time for the first bind to occur. In PPM mode (with a jumper added on the pcb…) the pulses stream is on the signal output of channel 1 / throttle connector. The others channels are not available on the connectors but the ESC output is still usable. See the picture of the waveforms: upper signal is from channel 1 connector, with the ESC output just below. The receptor does not feature cutoff for lipo protection: I tested that the ESC keeps driving a small motor with an input voltage as low as 2.4v. So be careful if you use a 1S lipo. 1.0mm 3-pin JST connectors are not available at Banggood, nor some tiny compatible servos. Just a pity... It is bit expensive if you compare it to a V911 of F929/939 receiver with 2 integrated servos

    Comentários (2)
    Mostrar original
  • 28/02/2018

    It is a really small and light receiver. The connectors are JST 1.0mm. It has been easily bound with my Flysky FS-i6 transmitter. Some instructions about the connections would be welcomed.

    Comentários (5)
    Mostrar original
  • 18/07/2017

    Some instructions would be helpful, the channels are not labeled, the connector for the lipo should be included and the labeling for the motor and battery are poorly labeled. The receiver starts in bind mode on my Ultimate 7E I select flysky and press bind and it binds. Ultimate 7E is Devo 7E with upgraded arm for more memory. I also heave installed a 3in1 multi module which was cheaper on aliexpress.

    Mostrar original
  • 12/03/2020

    Receptor super pequeno com controlador integrado para motores de escova. muito bom para pequenos panfletos internos. Somente os soquetes JST de 1mm não são adequados para servidores 1S com conectores JST principalmente de 1,25mm, mas há cabos adaptadores. Funciona perfeitamente!

    Comentários (2)
    Mostrar original
  • 01/08/2017

    it's tiny ! - the same size board as "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" and shares the same 1mm spaced pins in the servo sockets (compatible with hk-5320s servos), although the chip components are laid out differently size and weight consistent with descriptions way smaller than the wltoys f-series receiver (shown for comparison in the pic) the layout would presumably the same as the dsmx version for the wires - motor connections for the esc marked M on the left of the underside, and battery to the right; both with their positive lead on the middle (pair of) solder pads haven't tried it yet, but the dsmx version worked fine, and i expect this should too

    Mostrar original

    Total 0 Páginas

    Vá para página


    Você pode estar interessado em

    recommendation for you
    • R$64,44
    • R$164,11
    • R$111,34
    • R$310,68
    • R$36,88
    • R$35,18
    • R$29,26
    • R$52,24
    • R$76,16
    • R$35,12
    • R$334,14
    • R$498,30
    • R$820,77
    • R$738,69
    • R$117,20
    • R$128,93
    • R$492,44
    • R$134,79