Opiniões dos clientes

4.94 de 5
Escrever uma crítica
  • Todos Comentários (70)
  • Imagem (4)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(70)
    • Estrela(66)
    • Estrela(4)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
  • Helmuth
    2020-05-26 06:29:57

    the package MUST be improved. Some pins are plis

  • 2016-11-21 11:05:30

    Despite the small difference in appearance, the device is as as described. Everything works normally. Only problem I had when supplied with 12.14 volts. Although LEDs lit, no output voltage. I suppose that the maximum supply voltage is a little less than 12 volts.

  • 2018-04-26 03:33:40

    Used for Arduino projects - just search for "Arduino L9110S" on Google, and you will find Lib and examples. Even with a "short" on the motor side, I have not been able to "Kill" the board

  • bruno
    2018-05-05 14:36:55

    Pretty nice

  • 2020-07-05 23:06:12

    Works great. Only knocked down the rating because packaging wasn’t good and pins were bent.

  • 2017-03-26 18:18:35

    Tested with a pro mini and worked great. I had to try two different power plug supply's, one was 12.3 volts even though it was labeled as 12 volts and it did not work. It did not damage it but be careful it might. 12 volts might be its absolute max. I will probably use this with a 9 volts just to be safe

  • 2017-03-07 13:17:30

    Just be sure that you check the connections to match them with your circuit. (Vcc, GND, A1A, A1B,etc.) The connecting pins are in a different order than the ones on the controller shown in the diagrams in my project. Not a problem; the controller will work fine when you connect the wires correctly according to the labels printed on the board.

  • steve
    2016-01-31 17:03:54

    This little part has some punch when driving DC motors. I tested both drivers on my robot and they worked like a charm. But after measuring the current, it looks like the HD7881 chips do tend to heat up quite a bit when the load current exceeds ~350mA. Yes, the part is rated for 800mA, so it might make sense to add a small heat sink when dealing /w heavy loads. Otherwise, this is just perfect for small (i.e. light load) projects. I will definitely order more of these parts !

  • 2019-09-08 13:54:23

    Ottimo il materaiale ricevuto, La consegna è stata precisa e puntuale. Il rapporto qualità prezzo veramente ottimo. Ho provato le schede ricevute in associazione con i motori DC-3V-6V-Single-Axis-Gear-Reducer-Motor e funziona tutto in modo perfetto.

  • 2017-01-30 07:39:30

    Fonctionne bien, juste un petit problème esthétique, les deux sorties de connections moteurs sont soudées de travers légèrement décalées mais cela n'empêche pas leurs connections.


    Go to page


    Você pode estar interessado em

    recommendation for you
    • R$121,50
    • R$87,65
    • R$49,06
    • R$216,29
    • R$104,20
    • R$40,87
    • R$33,50
    • R$11,05
    • R$71,39
    • R$8,71
    • R$26,14
    • R$111,04
    • R$41,22
    • R$20,93
    • R$25,67
    • R$57,95
    • R$75,95
    • R$10,70