Opiniões dos clientes

4.76 de 5
Escrever uma crítica
  • Todos Comentários (17)
  • Imagem (3)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(17)
    • Estrela(13)
    • Estrela(4)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
  • November-11 2020 03:06:06

    They LIED in the description. I weighed the heat block, its anodised aluminium So if you want to print high temperature this is not the one to go for. I ordered both the normal and the high flow version. The high flow version has a copper heat block and and the block weighs 30g versus 8g The machining left a few small shavings visible stuck to the heat break that could jam a small nozzle so make sure you check and clean out. Otherwise its very smooth inside and the bimetal heat break and long

  • June-29 2020 18:03:12

    Drop-in replacement for E3D V6 and clones. Very easy to install, it takes less than one hour to start printing again. Comes in a nice box with accessories. I've received it today and I've already printed a lot; the heat creep problems I had with a j-head clone are just bad memories! The design is a real improvement. Worth buying for a printing experience without headaches!

    Comentários (1)
  • December-17 2020 16:42:52

    very good. no problem even with printing pla. recommend that but i am affraid to go over 320 °C.

  • January-06 2021 13:36:36

    Great product and comes in a nice package. Workmanship looks great, but make sure to remove nozzle and clean path with some filament before use, since I saw some debris from the burr at the end of the heat path just before the nozzle. Hot zone looks great, probably just as good as the far more expensive mosquito nozzle. The structural part is one piece, and the top is not removable via screws as in the original Dragon hotend which is twice the price. So the only way to attach it is via the groove

  • December-22 2020 01:47:14

    I bought this as an upgrade to V6 hotend. This needs a lot of active cooling to keep it cool. I use a radial fan (normally used for part cooling) and the results are amazing. I bought the short version which means it goes into my BMG direct drive the combination of both just a massive improvement.

  • May-27 2020 08:23:38

    Did not fire this up yet but wow, this is so cool and feels quality product. Did get the long range bowden version. So cute much beautiful. Very wow. Doge!

    Comentários (1)
  • January-14 2021 04:51:28

    Short distance verion purchased, arrived before delivery date, well packaged, nice compact hotend, Nozzle fitted to hotend was 0.3 not 0.4 as specified. Spare nozzles were 2x0.6, 2x0.3 and 2x0.2, should have been 2x0.6, 2x0.4, 2x0.3 Have not fitted the unit and therefore not used yet.

  • January-18 2021 09:02:36

    Welll made. Nozzle are smaller than normal. Fit is good. Did not installed yet.

  • January-02 2021 09:01:14

    good quality

  • November-23 2020 06:54:15

    encore mieux


    Total 0 pages

    Go to page


    Você pode estar interessado em

    recommendation for you
    • R$88,14
    • R$50,40
    • R$216,36
    • R$11,16
    • R$196,18
    • R$88,81
    • R$145,72
    • R$27,98
    • R$105,97
    • R$44,24
    • R$14,41
    • R$347,33
    • R$235,42
    • R$224,21
    • R$50,40
    • R$211,88
    • R$145,16
    • R$396,34