Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (562)
  • Imagem (68)
  • Vídeo (1)
  • Todas as estrelas
    • Todas as estrelas(562)
    • Estrela(543)
    • Estrela(17)
    • Estrela(2)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 16/11/2020

    Ele chegou muito rapidamente, em apenas 11 dias, em condições físicas completamente corretas. Ainda falta tentar. Este é um item ressentido, o anterior estava preso em algum lugar.

    Comentários
    Mostrar original
  • 13/07/2021

    muito bom

    Comentários
    Mostrar original
  • 13/02/2021

    Bem-parecido, ainda não o testei, mas não estou preocupado. veio num saco de segurança selado.

    Comentários
    Mostrar original
  • 26/01/2021

    muito bom, eu uso o controlador com um esboço de joystick e construi-o no meu jugo Saitek para eliminar a zona morta irritante neste jugo.

    Comentários
    Mostrar original
  • 08/10/2020

    Tudo bem, salve o pacote. Meu velho volante de jogos salvou :)

    Comentários
    Mostrar original
  • 10/06/2021

    Funciona perfeitamente! Pinos soldados facilmente e o código foi carregado e funcionou imediatamente.

    Comentários
    Mostrar original
  • 28/01/2021

    boa entrega, o item é bom, mas eu ainda não o usei porque ele chegou agora

    Comentários
    Mostrar original
  • 29/10/2020

    Parece-me bem.

    Comentários
    Mostrar original
  • 19/09/2020

    muito bom

    Comentários
    Mostrar original
  • 05/05/2019

    I ordered two of these boards and they arrived much faster than I expected and were in good condition. They were individually packed in static bags and came with two header pins as shown on the product page. Soldering them was easy - stick the pins into a breadboard and set the board down so the pins go through the holes. No need for any tools to hold everything in place. Windows 10 recognized the boards and installed the correct drivers automatically; the Arduino application saw them too and I was able to program them immediately. It worked! Note that while this board is compatible with a Leonardo (same MCU), the built-in LED on a Leonardo (on Pin 13) does not exist on this board. I ran into some trouble with one of them that was entirely my own fault. Based on the silkscreen markings on the board and its size, I thought I'd try using the SparkFun Pro Micro drivers. Things worked fine until I programmed the board, after which Windows would no longer recognize it as a usable USB device. Turns out the SparkFun Pro Micro comes in two flavours: 5V/16MHz and 3.3V/8MHz, and the driver defaults to 3.3V/8MHz. The solution to the problem is to change the board type in the Arduino application back to Leonardo (5V), then ground the /RST pin twice, quickly. After that, the bootloader will wait for eight seconds for you to set the Arduino software to the correct COM port and upload your program, making sure you have the board type set to Leonardo. It took me a couple of tries but I brought the board back from the dead. If you ever program your board and it no longer works and your computer can't seem to communicate with it anymore, try the above technique, or do a search for "pro-micro fail troubleshooting" it's where I got the above from. This is a great little board with more pins than you'd expect for a device this small, and it plugs nicely into a breadboard, leaving plenty of room for other components.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • R$32,94
    • R$16,44
    • R$32,94
    • R$49,43
    • R$32,94
    • R$43,94
    • R$15,34
    • R$27,44
    • R$54,93
    • R$80,45
    • R$43,94
    • R$54,93
    • R$604,81
    • R$60,43
    • R$76,93
    • R$247,39
    • R$29,64
    • R$54,93