Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (261)
  • Imagem (25)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(261)
    • Estrela(236)
    • Estrela(10)
    • Estrela(7)
    • Estrela(2)
    • Estrela(6)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 15/08/2017

    It is an impressive induction heater working at 85 kHz frequency. I have added a little improvements : cooper contact for coil, a fan cooler and refractory sponge-brick as coil / crucible support. I have tested with a switching power supply with DC output of 24V /20A using a graphite crucible (33mm diameter and 30mm height); the current was aprox. 18A and the crucible has reach 900C in 3-4 minutes; first i have start the power supply then i have connected the induction heater. i recommend this induction heater.

    Comentários
    Mostrar original
  • 26/03/2016

    Coil ID 1.700", OD ~2.160. Board (overall, including heat sinks) 4.400" x 3.950" x 1.520". All dims are approximate and rounded up to the next number that made any sense. Input voltage is marked for polarity (- terminal only) but neither voltage nor amperage are labeled. Again, like with the smaller unit, if you were hoping to receive some sort of documentation, you are out of luck. The copper tubing is not insulated so, despite the generous size of the coil, the electrical path will be quite short with the whole coil acting as if there is only a 1/8th turn unless you make the effort to isolate the tubing yourself. I've made no attempt to power this up yet, so all I can pass along are the physical attributes.

    Comentários (2)
    Mostrar original
  • 16/09/2022

    dispositivo muito gdeud. O segredo é que você precisa de uma grande fonte de alimentação. Primeiro usei um Ps caseiro de dois transformadores do microondas 40 v 25 A. Mais tarde usei um ps de um transformador 25 v e muitos Amps de uma máquina de cinema dos anos 1970. Consegui um pedaço de ferro vermelho com 25 mm de diâmetro em 90 segundos. Uma boa corrente é 20-32 V 15 A . Não use mais de 20 A por muito tempo para não queimar os mosfets. A indução começa depois de 12 v.I ter usado um ventilador de um forno de microondas para manter o dissipador de calor do mosfet fresco. No grande ps i usei um retificador Bridgfe de 35 A com dissipador de calor grande e um ventilador do computador (12 v). Não coloque itens com diâmetro superior a 3 cm e superior a 4-5 cm de comprimento para manter os amps inferiores a 20.Se você Use um regulador de voltagem com triac no primário do transformador. A voltagem deve ser superior a 150 v para não queimar a ponte.É melhor usar uma variac para ter sempre uma onda seno completa em cada voltagem que você precisa.

    Comentários (2)
    Mostrar original
  • 26/11/2016

    Szybka wysyłka, szybko grzeje, na zdjęciu zasilacze serwerowe do zasilania. Przy większych mocach potrzebny wiatrak chłodzący i chłodzenie wodą. Polecam.

    Comentários
    Mostrar original
  • C4WRC
    FR
    29/03/2018

    Voici un petit système de chauffage à induction très compact et pratique qui va m'être très utile pour mes bricolages, il me reste a lui faire un boitier

    Comentários
    Mostrar original
  • 17/12/2016

    This very functional inductive heater has become a hot item. You can do many things with this system. Because of high current/stability. best to use 4 X 12 VDC leadgel batteries of minimal 12 AH (better 17AH) IN SERIE to feed this system Use one of the batteries to power a fan for the electronic parts too. Switshing powersupplies are less /not suitable, the fast slope of the drained current can interfere / not starting oscillation. So be wise , use as alternative a 1KW 35VAC ringwound trafo, rectifiers and a lot of switshingproof elco's in parallel. A Variac can be used but start up in full mode and than reduce voltage. When cooling s OK and powersupply is sufficient the only big problem is to start the oscillationprocess (It is self oscillating). !000Watt is quite a lot, the smaller ones I have bought first are already nasty heaters wich can heat up a nail in seconds.

    Comentários (1)
    Mostrar original
  • 27/12/2021

    O produto é de qualidade muito baixa. Transístores nos radiadores de resfriamento sem composto térmico, um transistor não se encaixa no radiador de resfriamento. Uma extremidade do enrolamento da drose não é soldada no tabuleiro. Ao ligar o transístor zadraschiem em modo sparing.Ocht uma impressão muito ruim do produto.

    Comentários
    Mostrar original
  • 02/06/2017

    Nagrzewnica działa dobrze , wymaga chłodzenia przy dłuższej pracy. Kiedy mam już podpięte zasilanie pod zasilacz i włączam go to nagrzewnica nie startuje za każdym razem . Ale jak podpinam przewód zasilający do włączonego już zasilacza to działa od razu OK . Widocznie powolny czas narastania napięcia przeszkadza w pewnym starcie nagrzewnicy.Tu na zdjęciu tak na próbę dałem 28v i 5,7A ,4mm gwoźdź się rozgrzał w jakieś 20-25s. Na luzie pobiera w tym momencie 28v i 3,6A . Dzisiaj przyszła więc to takie pierwsze uruchomienie

    Comentários (1)
    Mostrar original
  • 14/04/2016

    Used the heater to silver braze a very small SS tube to a much larger SS part. This was a problem with a torch since the parts were so dissimilar in size. The heating with the induction heater was very uniform and did an excellent job. Overheating of the flux was a problem with the torch, but not with the induction heater. Heating cycle was about 2.5 minutes.

    Comentários
    Mostrar original
  • 05/04/2018

    Estoy haciendo unos experimentos, usando el circuito Geekcreit ZVS dentro de otro ideado por Tesla. Ya os contaré como me fue. Creo que con este circuito resuena con intensidad suficiente para hacer funcionar el circuito diseñado por Nikola Tesla. la Patente 685.957 : Método de utilización de la Energía Radiante la Patente 512.340 donde una genialidad de Nikola: la Bobina Bifilar tiene la clave de la resonancia armónica, es como condensador de flujo electro-plasmático, capaz de enfriar la energía de la Red Eléctrica: separar magnetismo y electricidad, resultando que el coseno de Phi de la energía consumida tiende a 0 significa que podemos ahorrar en consumo un 100 % y tener una nueva forma de energía eléctrica fresca, no peligrosa, saludable y natural.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$323.00
    • US$99.99
    • US$36.99
    • US$229.00
    • US$34.36
    • US$139.00
    • US$64.99
    • US$18.59
    • US$85.49
    • US$84.99
    • US$71.99
    • US$75.59
    • US$97.99
    • US$12.99
    • US$19.99
    • US$77.99
    • US$22.99
    • US$21.19