Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (637)
  • Imagem (68)
  • Vídeo (4)
  • Todas as estrelas
    • Todas as estrelas(637)
    • Estrela(595)
    • Estrela(32)
    • Estrela(6)
    • Estrela(3)
    • Estrela(1)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 29/09/2015

    I took a chance on this, because I didn't think there was enough information in the description. I ordered the C version, with the 8x20mm motor, but unfortunately what arrived today was the A version, with 7x16mm motor, so the figures below are for the A version. I haven't powered it up yet, but I think it will be very suitable for an indoor slow flyer of the Vapor, Ember, Cub etc. style. With the 8x20mm motor probably something a bit bigger and/or faster. The prop has a diameter of 138mm, but no pitch marked. By comparing it with other props of known pitch I am guessing it is a 138x63 mm or 5425 inches. It came badly out of balance, but by taking tiny shavings off the heavy blade with a modelling knife, I eventually got it to balance perfectly. It is very light at 1.24g, and I don't think it would withstand a hard impact, but ideal for a slow flyer. The description says it has a .8mm hole, but when I measured the prop shaft, it is 1mm diameter. I tried pushing it into the prop and it is a very tight fit, but does go in. The gearbox is the usual two brass bush type, with plastic 9 tooth pinion and gear. I didn't count the teeth on the gear, but I'm guessing there are 54 giving a 6:1 ratio. The prop shaft is 27mm long with one end knurled for a length of about 8mm. I think the knurled end goes into the plastic nut provided, with the smooth end going into the prop, so you can remove and replace a prop without much trouble. Weight of the gearbox is 1.29g and of the motor 2.61g. Motor shaft is 1mm diameter. There is a square hole in the gearbox that I think is intended for mounting on the end of a square section carbon fibre rod, such as you might use for the fuselage of a very light slow flyer of the Vapor type. It looks as though it is a 2x2mm hole. It would probably be possible to mount the motor/gearbox other ways, e.g. with tiny cable ties or with glue. The proof will be in how it runs, but at this stage I think it's a very light and economical power plant for an indoor flyer, with flexibility in the choice of motor according to your intended use.

    Comentários (5)
    Mostrar original
  • 07/08/2019

    Great micro motor for ultra light aircraft under 4 ounces. It ships unassembled but assembly is easy. The propeller balance should be checked and corrected before use. The gear is a little noisy at low rpm but it smooths out at flying speed. I used one in a Guillow's Lancer airplane I converted from rubber power to electric motor and 3 channel RC. This motor and propeller provide more than enough thrust for this under 50 gram airplane.

    Comentários (2)
    Mostrar original
  • 26/09/2018

    Nice Motor....... Enough Thrust power to my DIY plane.....

    Comentários (1)
    Mostrar original
  • 12/12/2020

    Kit de unidade de folheto lento fino e leve. Não foram fornecidas instruções de assistência, por isso deve olhar bem para a imagem antes de montá-la. As buchas devem estar bem alinhadas, caso contrário o eixo tende a prender e a correr com alta fricção. O meu kit tira 80mA a 4.0V (na lipoaspiração de 1 s) e mostra alguma vibração - equilibrará a hélice e verá se puxa o suficiente para o meu panfleto interior...

    Comentários
    Mostrar original
  • gozVIP3
    CA
    03/12/2020

    pequeno motor bonito você no entanto tem que ajustar o corte do acelerador para ter um impulso de arranque, caso contrário o motor não funciona, eu o coloquei em uma mini beechcraft de banggood

    Comentários (1)
    Mostrar original
  • 14/10/2020

    Entrega rápida, condições perfeitas, mal posso esperar para começar a construir

    Comentários
    Mostrar original
  • 08/11/2017

    this item is very good has super power i use for mini cessna airplain fly very good https://www.youtube.com/watch?v=sOhNC9UEu_U&feature=youtu.be

    Comentários (1)
    Mostrar original
  • 24/11/2018

    nice product but motor shaft is very tigh t and motor casing is very tight too you have to make that bigger to fit

    Comentários
    Mostrar original
  • 31/08/2017

    Works perfectly fine for small indoor models.

    Comentários
    Mostrar original
  • 28/09/2016

    I found the easiest way to mount the 8x20 version was to drill mounting holes in a WLtoys F929 motor base and push it onto the end of the motor of this unit and secure with a dab of superglue or epoxy as in my picture. To adapt the shaft for a Gemfan style 5030 or 6030 prop I soldered a piece of 2mm diameter brass tubing 8mm long inside another piece of 3mm brass tube and soldered them both onto the shaft .I then use a piece of silicon or plastic tubing to get a friction fit between the prop and the 3mm tubing. http://www.banggood.com/WLtoys-F929-F939-RC-Airplane-Spare-Part-Motor-Base-with-Propeller-022-p-947009.html http://www.banggood.com/Gemfan-5030-6030-7035-8040-8060-9050-1060-Direct-Drive-Propeller-1-pcs-p-973633.html

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$23.99
    • US$14.99
    • US$36.99
    • US$73.99
    • US$9.99
    • US$10.90
    • US$21.99
    • US$9.69
    • US$25.00
    • US$9.99
    • US$7.99
    • US$20.50
    • US$8.99
    • US$47.99
    • US$13.99
    • US$17.99
    • US$33.90
    • US$89.99