Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (17)
  • Imagem (1)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(17)
    • Estrela(16)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
    • Estrela(1)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 04/12/2018

    My bus has a 3126 Caterpillar turbo-diesel engine that requires 28 quarts of oil and is very hard to start on cold winter mornings. I installed three of these oil pan heater pads and they take about two hours to bring the oil pan temperature from +20F to +50F, then my engine starts right up. I just put these on this year so I am hoping they are as durable as they are effective, but so far so good so I give these heater pads a good recommendation.

    Mostrar original
  • 24/03/2016

    I used this Heater to build a Prototype Bread Proofer using an outboard Temp Controller. Longevity is the key question as I've used it less than 24 Hours total. No installation Instructions are available from the supplier, so below is install steps that I have found elsewhere to be the most helpful: NSTALLATION INSTRUCTIONS • 1. Clean the selected installation area to remove any dirt, grease or oil - a pressure washer works great for this. • 2. Grind or sand all paint from the surface area slightly larger than the heater. Do not polish this surface. A coarsely scratched surface is best. HEATER MUST BE PLACED ON METAL SURFACE. • 3. Use acetone, lacquer thinner or similar agent to wipe the area clean. If these recommended cleaners are not available a strong detergent scrubbing followed by a thorough fresh water rinse and towel dry will do. The surface must be absolutely clean. DO NOT USE Gasoline • Solvents • Spray Penetrants • Diesel Fuel • Any product that leaves oily film DO NOT CUT OR TRIM HEATER! • 4. Remove the protective covering from the pressure sensitive adhesive. AVOID TOUCHING THE ADHESIVE. Decide which direction you want the cord to go. Plug in the pad for 3 to 5 SECONDS to warm the adhesive. WARNING: The pad will become very hot if plugged in longer and may burn exposed skin or damage heater. Unplug pad before applying to metal surface. • 5. Place the edge opposite the cord on the clean surface. With a squeegee (supplied in kit) apply maximum pressure as you affix the pad. Carefully avoid wrinkles or creases; smooth the entire pad to the surface. • 6. Attach the first length of AC cord with a cord tie. (supplied in kit). This prevents the weight of the cord from pulling down on the pad. • 7. Plug the heater in for 5 to 10 SECONDS, unplug and squeegee the pad again. DO THIS TWICE! • 8. Apply a small bead of high temperature silicone adhesive (supplied in kit) around the outside edge of the heating pad. DO NOT force the silicone under the pad. It is important to seal the entire perimeter of the pad for weatherproofing. DO NOT USE ANY OTHER ADHESIVES TO APPLY PAD TO METAL SURFACE! • 9. Route and secure the rest of the AC cord to a convenient location, such as through the grille. Avoid any moving or high temperature parts. Position the power cord so it is held snugly against the oil pan. Plastic ties are provided for use in securing/routing the power cord. • 10. Keep all NON-METAL surfaces such as plastic oil pan covers, noise suppressors, rock guards, fiberglass shrouds etc. to avoid melting, warping or fire hazard. AFTER INSTALLATION DO NOT USE THE HEATER FOR 24 HOURS AFTER INSTALLATION OF THE PREHEATER. THE ADHESIVE BOND WILL DOUBLE IN 24 HOURS IF NOT USED Hope this is of help to others!

    Comentários (1)
    Mostrar original
  • 02/02/2018

    Produit conforme à la description, 13 X 9 cm (5 1/4" X 3 5/8"), résistance de 70 ohms. pas essayer encore, j'attends de le coller avant de le brancher.

    Mostrar original
  • 29/01/2018

    I is the same thing you would by at Canadian tire. For about 11.00 bucks no duty or taxes.works great. And there`s would be over 100.00 bucks. You get with plug end or without.

    Mostrar original
  • 05/07/2018

    great little heater. put one on my solvent tank for winter use and works great. also 1 sixth the cost of locally sourced one

    Mostrar original
  • 19/01/2016

    i put this on my oil pan thinking it would not do much well i was wrong it works great

    Mostrar original
  • Shoaib

    Realimentação positiva

    Mostrar original
  • 18/01/2020


    Mostrar original
  • 07/01/2020

    foi como anunciado. Todos estão trabalhando sem problemas até o momento.

    Mostrar original
  • 23/05/2019

    satisfied. thanks 😊

    Mostrar original

    Total 0 Páginas

    Vá para página


    Você pode estar interessado em

    recommendation for you
    • R$60,43
    • R$62,63
    • R$49,43
    • R$27,22
    • R$107,83
    • R$49,43
    • R$47,67
    • R$21,94
    • R$21,28
    • R$30,96
    • R$329,87
    • R$123,67
    • R$49,43
    • R$258,39
    • R$88,25
    • R$104,15
    • R$38,44
    • R$120,31