Opiniões dos clientes

4.89 de 5
Escrever uma crítica
  • Todos Comentários (221)
  • Imagem (25)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(221)
    • Estrela(205)
    • Estrela(11)
    • Estrela(3)
    • Estrela(0)
    • Estrela(2)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
  • February-22 2020 11:10:40

    Good product. Reads temperature, humidity, pressure and altitude. Tested the values with internet, and the values are a bit off, but all in all accurate enough. Note that this is a BME280 clone with SPI bus and won't work with I2C. Used some extra days on shipping, but I'm still overall pleased with my purchase.

    Comentários
  • April-18 2020 08:19:37

    Globalement bon produit, bonne fabrication, mais qualité moyenne, emballage antistatique

    Comentários
  • October-06 2020 10:42:09

    Good quality. Works well

    Comentários
  • October-01 2020 12:59:23

    Good price an quality.

    Comentários
  • January-31 2020 05:21:29

    Always a fantastic product

    Comentários
  • September-09 2020 10:51:52

    Fast delivery, proper packaging, testing in progress. Thanks

    Comentários
  • May-05 2019 03:18:24

    the model received is not exactly of the image, but it's a true BME280 and works perfectly. the breadboard contains a pull-up resistors, necessary for I2C and SPI protocols. I have worked directly on arduino, but for security, you use a level-shifter for adapt the logic levels (5v-to-3.3v). pd. I see multiple comments that say that module is not a BME280, is a BMP280. The marks on the module can induce an error, but the chip is a REAL BME280 and reads good the temperature, pressure and humidity

    Comentários (1)
  • February-23 2018 14:56:34

    I just hooked this up to an ESP8266 NodeMCU board using the Arduino IDE and firmware and it works great with the Adafruit BME280 library. Like others have said, I just had to change the I2C address to 0x76. The temp and humidity values seem comparable to the readings I was getting from the DHT22 sensor that I replaced with this because I also wanted barometric pressure readings. Wish these would be a bit cheaper but I only need one of them, the rest of my boards will be fine with DHT22s for temperature

    Comentários
  • October-17 2019 08:38:34

    this is NOT the BME280, I got BMP280 with no humidity reported by the sensor. The marking on the chip shows it, too, as I know for now. I trusted the reviews, but obviously they changed the board. You can look it up in the data sheets: BME280: https://www.embeddedadventures.com/datasheets/BME280.pdf (chapter 7.7) BMP280: https://cdn-shop.adafruit.com/datasheets/BST-BMP280-DS001-11.pdf (chapter 7.3) The BME280 with humidity measurement has one dot and one vent hole, the BMP280 only has one dot -

    Comentários
  • December-30 2016 04:02:53

    Can work I2C or SPI. In the picture work SPI. Nice accuracy and resolution data :) Recommend. Descriptions of parameters shown in the attached image in Polish ;)

    Comentários
Show:

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • R$72,31
    • R$30,05
    • R$39,12
    • R$37,44
    • R$27,93
    • R$49,19
    • R$68,11
    • R$7,22
    • R$50,31
    • R$16,73
    • R$48,52
    • R$7,22
    • R$22,33
    • R$50,31
    • R$134,26
    • R$262,98
    • R$31,96
    • R$156,65