Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (207)
  • Imagem (21)
  • Vídeo (2)
  • Todas as estrelas
    • Todas as estrelas(207)
    • Estrela(183)
    • Estrela(10)
    • Estrela(8)
    • Estrela(2)
    • Estrela(4)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 16/09/2017

    It seems that there´s a huge mistake maken in the description. Voltage Output for Safety Switches on MY Anet A8 is 5V. This sensor, however, needs 10-30V´s working Voltage...The led also stays dark, which is very useless for configuration. It´s kinda bad that my printer arrived about 1month later, so now i can´t return it back. People be aware and measure the output Voltage on the S_Z-Port on your A8-Mainboard!!

    Comentários
    Mostrar original
  • 02/09/2017

    Leider nicht so 100 Prozentig. Um die Montage zu erleichtern wird eine Leiste mit zwei Schrauben auf der Rückseite befestigt, sie sollen die Gewindemutter für den Geber fixieren, leider ist die Schlüsselweite von 6mm zu groß für die Mutter (SW 5,5) beim festziehen der Schrauben kann recht schnell die Mutter durchdrehen. Die Schrauben von der Leiste sind von der Geberseite montiert, welches zur Folge haben kann das sie nicht an der Führungskassette vorbei kommen, Abhilfe die Schrauben von der Rückseite durch stecken und den Kopf versenken. Ich finde diese Lösung etwas halbherzig, schöner Schriftzug (leider nur von der Rückseite lesbar), aber nicht mal Unterlegscheiben.

    Comentários
    Mostrar original
  • 28/07/2021

    O que tenho a dizer sobre isto? O cabo e o conector são de boa qualidade, tive que virar as cores, ele voltou perfeitamente, mesmo após desmontagem. Tenha cuidado com o suporte fornecido para o sensor de nível automático, pois ele é altamente frágil. Partiu-se para mim quando o puxei. O suporte e o empate são feitos para o mosfet. Há 3 dos ferros no pacote que você pode usar como um extra

    Comentários
    Mostrar original
  • 02/09/2019

    recebido hoje dia 02-09-2019, embalado saco plástico, aparentemente perfeito sem nenhum problema, ainda não não testei.

    Comentários
    Mostrar original
  • 01/04/2019

    Tudo certo

    Comentários
    Mostrar original
  • 14/02/2019

    The sensor was delivered to me. In testing I found it does not work with the original firmware on ANET. You need to use MARLIN or SKYNET 3D. So I can not write whether it is operational. When I change the firmware I test the sensor. Nevertheless, 5 stars.

    Comentários
    Mostrar original
  • 07/02/2019

    Produto excelente.

    Comentários
    Mostrar original
  • 22/09/2017

    La pieza se ve de buena calidad y probablemente funcione muy bien sin embargo se les ocurrio embalar juntos en un solo empaque varios articulos uno de los cuales pesa mas de 300 gramos y es completamente metalico y pues este articulo tiene una base de acrilico asi que no soporto y llego fracturada en 3 piezas... Espero puedan dar una solucion para este problema.

    Comentários
    Mostrar original
  • 09/07/2017

    quality auto-leveling sensor with holder. Anet original. instructions to attach and use it are found on YouTube very easy to do it.

    Comentários
    Mostrar original
  • 31/08/2017

    Complicated setup, but works well once this is done. Be careful, though, as there is no support behind the screws which hold it in place, and the acrylic backplate cracks very easily if the screws are overtightened. A piece of 5mm material beteen the bearings will give support where needed.

    Comentários (1)
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai
    recommendation for you
    • US$19.99
    • US$16.99
    • US$6.99
    • US$49.99
    • US$39.99
    • US$7.56
    • US$39.99
    • US$63.99
    • US$17.99
    • US$25.99
    • US$48.99
    • US$15.99
    • US$22.99
    • US$43.99
    • US$43.99
    • US$21.99
    • US$32.99
    • US$29.99