Opiniões dos clientes

4.97 de 5
Escrever uma crítica
  • Todos Comentários (69)
  • Imagem (7)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(69)
    • Estrela(67)
    • Estrela(2)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
  • Mundek

    Installed two of them on two different Devo transmitters and both work great. Lets you to fly many drones, quadcopters, hexacopters, boats, cars, planes, helicopters, etc. Highly Recommended.

  • 29/09/2016

    It works as expected and now I can fly my Hubsan X4 with my Devo 7e (it even has voltage telemetry)! It does not include any wires or directions, so do a little homework beforehand. I used the 'new wiring' for the install. Basically, pad 6 gets bridged to 9, and 7 gets bridged to 8. The photo included shows the other connections, but the pads haven't been bridged in this case. TXEN gets connected to GI01 and RXEN gets connected to GI02 instead of GND and VCC as shown. Every pad will have just one wire coming from it when done correctly. And, don't forget to update the hardware.ini file afterwards!

  • 05/05/2016

    This module arrived in good shape. I added this module to my Devo7E transmitter and it works perfectly. I tested it on a Husban quad and it was able to bind immediately. This was the second module that I've added to my transmitter and I've experienced perfect radio communication with it. I've flow it out as far as I can see/control the quad and had perfect control the whole time - no range issues. I'm very happy with this product.

  • 07/03/2017

    As decribed

  • 08/04/2016

    Have it installed on my Devo7e and everything works as expected. Soldering was easy and i´m happy about that everything works ;) Thx Banggood !

  • 12/09/2017

    great tx module to complete my multi Tx FrSky Taranis Module

  • 28/02/2017

    Works perfectly on my DEVO 7e.

  • 11/04/2016

    Very happy with the purchase. Now I can control the Hubsan X4 flight controller with Walkera Devo10. With greatly extended control range. Follow the instructions on the picture. VCC wire goes to 3.3V and black to TMS, which is marked on the board inside your radio. Once wiring is completed, enable module in tx.in file. enable-a7105 = A13 has_pa-a7105 = 1 If you don't want to configure model, add settings from forums into your model file. Enjoy

  • 10/04/2015

    Не хотел запаивать модули непосредственно к плате аппаратуры. Вывел с платы своего Devo10E два шлейфа с 6-пиновыми jst коннектороми, зацепил такие же шлейфы на модули, этот и NRF24L01 http://www.banggood.com/DEVO-Transmitter-Tuner-Modified-for-FBL80-FBL100-WLtoys-V922-p-89812.html так же с коннекторами на конце. Соединил их и получил сменные модули установленные внутри корпуса Devo. Антенны расположил внутри корпуса вдоль задней стенки. Прошил аппаратуру последней прошивкой Deviation, настроил конфигурации моделей. Теперь мой Devo управляет всеми моими вертолетами wltoys v911, 913, 922, walkera V450D03 и будущим еще не собранным квадрокоптером. Доволен как слон

  • autrion

    I am using it in combination with this antenna : http://eu.banggood.com/FPV-5_8GHz-Micro-CL-TX-Anternna-0_8g-Lightweight-p-973291.html The only thing is that you will have to use some kind of voltage stabilization and filtering. But I am using it anyway on my Hubsan X4 with carbon fibre frame mod and it is still possible to fly FPV.


    Total 0 Páginas

    Vá para página

    recommendation for you
    • R$375,93
    • R$127,04
    • R$111,15
    • R$370,63
    • R$285,90
    • R$68,79
    • R$121,74
    • R$63,49
    • R$476,54
    • R$333,56
    • R$79,38
    • R$248,83
    • R$42,31
    • R$248,83
    • R$217,06
    • R$1.588,59
    • R$121,74
    • R$471,24