Opiniões dos clientes

4.77 de 5
Escrever uma crítica
  • Todos Comentários (97)
  • Imagem (11)
  • Vídeo (8)
  • Todas as estrelas
    • Todas as estrelas(97)
    • Estrela(83)
    • Estrela(8)
    • Estrela(4)
    • Estrela(2)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
  • December-27 2017 04:54:40

    Hello Banggood, I built the EleksMill together and the machine works very well. Although I am not so satisfied with the 500mW laser because the performance is a bit too weak for me, luckily I could mount the 2.5W laser from my EleksDRAW and the results were very satisfactory. The motives were made with the 2.5W laser I'll still order the ElexLaser A5 Pro 5.5W for sure. Great machine.

    Comentários (1)
  • November-10 2016 21:17:44

    La maquina esta tal cual muestra en las imágenes, hay que configurar algunas cosas que no aparecen en la explicación del producto recomiendo leer acerca de GRBL que es el controlador que se le instala al arduino nano https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.9, si necesitan precision hay que cambiar los step/mm yo lo coloque de 400steps/mm. los tornillos son de 2mm de paso. hasta ahora he trabajado con madera dura y blanda no he tenido problemas. Recomiendo eso si comprar disipadores para los controladores ya que vienen sin estos y se calientan mucho.

    Comentários
  • May-06 2017 11:12:15

    Machine is better than i expected. Solid, durable and good looking. Dont be afraid of assebling. Its easy, just follow the instructions on their website. I could not use some washers because some screws were short but there was no problem. Machine can manage intricate engravings very well. If you use proper tools and settings, it can cut thin copper and brass without any modifications or upgrades. Im using 1mm flat end mill, 0.1mm stepdown, 0.1 plunge rate and 0.2mm feed rate for profiling 0.5mm brass and copper. Result in in the picture below. And dont forget to lubricate metal parts.

    Comentários
  • December-01 2017 04:25:47

    The kit is very comprehensive you even get spares and almost all the tools you need. Easy to assemble just make sure you pay close attention to the pictures otherwise you easily get things backwards! Plenty of software on the web I’m using Universal Gcode Sender and Easel to learn. on my machine the Y and Z axis needed to be reversed to make it work. But otherwise works great. I’m just learning how to use it properly. be prepared to break milling bits if you’re doing fine work.

    Comentários
  • May-12 2017 09:43:06

    Пришло за 14 дней, упаковано отлично, всё есть в комплекте, крепежа немного больше. В комплекте нет инструкции по сборке и софта - но всё это есть на сайте производителя и много видео в YouTube - так что проблем со сборкой быть не должно. Линейные подшипники, чтобы направляющие свободно перемещались под своим весом - придется подрегулировать какое-то время. It came in 14 days, packed perfectly everything is in the kit, fastening a little more. In the complete set there are no instructions on assemblage and a software - but all this is on a site of the manufacturer and it is a lot of video in YouTube - so problems with assembly should not be. Linear bearings, so that the guides move freely under their weight - will have to adjust for a while.

    Comentários
  • April-02 2018 15:56:42

    Fácil montaje en un par de tardes se monta es un poco lioso al principio el tema del software pero se acaba pillando el truco vengo de la impresión 3D recomendable

    Comentários
  • November-18 2016 03:44:28

    Be aware that, at least the unit I received: - comes with extra T8 and M3x40 screws to make the rods more stable to vibration and wobbling - has no M3x16 screws (use provided M3x18 for the rod supports and M3x14 otherwise) - has no M6x16 screws (use the provided M5x16) This is NOT BAD, even gives extra simplicity in assembly and extra stability! I explain it in my video posted below. Otherwise, this unit is great and works flawlessly. Have attention on "digging too deep" in hard woods. Do small Z-steps (ArtCam supports this "Do multiple Z passes"). For engraving you can also use InkScape and the GRBL plugin to do vector engraving instead of raster (much MUCH faster!). The controller on the unit is great and I realized how to use it great with all software. I also have an A3 laser kit from Banggood which uses a similar controller and, based on this, I've been able to adapt it to switch between Benbox and GRBL modes without having to change the hardware.

    Comentários
  • October-27 2017 03:42:51

    Produto com construção firme e materiais de boa qualidade. Faltou vir com dissipadores nos drivers pois eles aquecem bastante durante o trabalho.

    Comentários
  • March-23 2017 07:51:09

    Eleksmill works good, but i see the "negative" of a model (on photo) The Z axis is change buy your recomendation in opinions (from 0 to 4) Please help me)

    Comentários
  • August-21 2018 10:43:17

    verey good machine for to beging cnc works for use at home

    Comentários (2)
Show:

    Total 0 pages

    Go to page

    Go

    Você pode estar interessado em

    recommendation for you
    • R$917,45
    • R$963,32
    • R$1.083,74
    • R$2.236,36
    • R$401,35
    • R$1.548,23
    • R$917,45
    • R$688,07
    • R$1.267,25
    • R$1.277,57
    • R$1.433,54
    • R$2.006,98
    • R$1.548,23
    • R$1.318,85
    • R$1.146,82
    • R$1.318,85
    • R$1.548,23
    • R$121,00