Opiniões dos clientes

Escrever uma crítica
  • Todos Comentários (105)
  • Imagem (5)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(105)
    • Estrela(94)
    • Estrela(7)
    • Estrela(2)
    • Estrela(0)
    • Estrela(2)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 05/01/2021

    excelente produto, chegada rápida, 12 dias

    Comentários
    Mostrar original
  • 16/03/2015

    Sehr gute Fräser mit 1/8" Aufnahme und auch 1/8" Schneide. Ich fräse momentan Eiche und Buche massiv damit, was einwandfrei funktioniert. Sehr glatte Fräskanten und sauberer Rundlauf. Die 3.175mm Fräser habe ich sonst nirgends gefunden. Glatte Schulnote 1!

    Comentários
    Mostrar original
  • 23/11/2019

    They came as shown, I did a runout test and vibration/balance test to compare to my onsurd bits. Run out was the same on the shank I could not compare the tip due to a single flute, but seems fine @ 18,000 rpm they did seem to make a bit of a different harmonic then the Onsurd but I would not say a balance issue more I think the way the air was interacting with it. Speed and feeds were the same as Onsurd in HDPE really the only difference were pocket floors were not as clean with some engine turning marks which could be a pro or con depending on your work. But with a few speed n feed tweaks I bet I could get them cleaned up but threw cut sidewalls where perfect. The big take away is i got 10 for less then one Onsurd so even if they wear faster or i crash one the value is there. I am a big believer in good tooling in metal, but for woods and plastics I'm willing to try value bits and these do make sense for general riping. Tested on a Multicam router

    Comentários
    Mostrar original
  • 20/04/2021

    Very good mills router bit .

    Comentários
    Mostrar original
  • 12/01/2021

    Excelente

    Comentários
    Mostrar original
  • 19/02/2020

    Ferramenta muito boa para corte multimadeira. O acabamento foi bom. Verifique somente o tipo de material e uma configuração nas opções de ferramentas como "subir" ou "Convencional". Em algum material, escolha a opção de subida para o acabamento da aresta. e alguma opção convencional para o melhor acabamento. E o corte ACP foi bom. Todos os produtos são muito bons. e também boa qualidade. Eu experimentei que as ferramentas são muito boas para usar na minha máquina de roteador. Os produtos foram entregues o mais cedo possível. Também gosto daquela entrega rápida.

    Comentários
    Mostrar original
  • 25/07/2016

    Reçues rapidement Une fraise cassée ...ce n'est pas grave , il en reste 9 :)

    Comentários
    Mostrar original
  • 15/05/2022

    Just got these , they look great , can't wait to see how they perform

    Comentários
    Mostrar original
  • 08/03/2022

    Obrigado, o pacote chegou. 😊

    Comentários
    Mostrar original
  • 25/02/2022

    perfeito, como descrito.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • US$80.99
    • US$36.99
    • US$21.03
    • US$5.99
    • US$22.99
    • US$32.99
    • US$9.65
    • US$63.99
    • US$13.99
    • US$18.99
    • US$49.99
    • US$9.99
    • US$4.99
    • US$42.99
    • US$22.99
    • US$21.99
    • US$6.55
    • US$3.59