Opiniões dos clientes

4.97 de 5
Escrever uma crítica
  • Todos Comentários (37)
  • Imagem (1)
  • Vídeo (0)
  • Todas as estrelas
    • Todas as estrelas(37)
    • Estrela(36)
    • Estrela(1)
    • Estrela(0)
    • Estrela(0)
    • Estrela(0)
Ordenar por:
Comentários Anteriores
  • Comentários Anteriores
  • Mais úteis
  • Mais Recente
Comentários apenas do seu país (Brazil)
|
Mostrar original

Uma parte da revisão foi traduzida automaticamente.

  • 24/01/2018

    I have been buying a lot of parts from Banggood. Normally the quality is good/very good. This time the quality is very bad. When installing on my lathe machine i measure a run-out of 0.17mm. On the chuck itself as well as on a clamped shaft. (new mill) It should be a high precision tool, so 0,17 run-out is totally unacceptable. My regular 3-jaw chuck has a run-out of 0.01mm. I can send a video, but i could not place it here. How can i place the video of the run-out? I would like a refund, or a new one of better quality.

    Comentários (1)
    Mostrar original
  • 20/04/2021

    Chegou a mim no Reino Unido rapidamente, como descrito não verificou a precisão, mas muito bom vendedor obrigado muito

    Comentários
    Mostrar original
  • 29/04/2021

    Alles wie beschrieben, schnelle Lieferung

    Comentários
    Mostrar original
  • 03/04/2021

    Parece bem até agora, mas ainda não o testei. Por agora, vou dar-lhe 5 estrelas

    Comentários
    Mostrar original
  • 02/02/2021

    parecendo bem, deveria ter comprado a placa traseira

    Comentários
    Mostrar original
  • 19/01/2021

    Excelente material a bom preço

    Comentários
    Mostrar original
  • 13/08/2020

    Está bem, está bem.

    Comentários
    Mostrar original
  • 17/07/2020

    Ainda não tentou, mas parece boa qualidade

    Comentários
    Mostrar original
  • 15/01/2018

    But you have to be aware of one things befor buying this chuck: You HAVE TO install it properly with virtually ZERO runout on your spindel/adapter. If you have any TIR ON YOUR SPINDLE/adapter plate it will be multiplied eith chuck. To avoid it, you will probably have to turn your adapter plate on YOUR lathe to have it true for YOUR lathe. Once that done you will be able to set your chuck tru with ZERO runout. Mine is dead on with absolutely NO runout. Not even tenth!

    Comentários
    Mostrar original
  • 23/06/2017

    The chuck is visually excellent, i.e., all surfaces are flawless without excessive machining marks. Indexing recess have a nice sliding fit on my mini lathe spindle. The spindle OD thread is precisely made enabling comfortable collet nut tightening. A somewhat superficial run out measurement by DTI and 16 mm end mill fixed in chuck show less than 0.01 mm TIR. Obviously this run out include the spindle and end mill inaccuracy as well as collet eccentricity. Hopefully TIR could be further reduced by increasing spindle bearing preload and finding a optimal mounting orientation on the late spindle.

    Comentários
    Mostrar original
Show:

    Total 0 Páginas

    Vá para página

    Vai

    Você pode estar interessado em

    recommendation for you
    • R$62,82
    • R$13,05
    • R$62,82
    • R$16,29
    • R$27,51
    • R$57,58
    • R$16,19
    • R$8,85
    • R$57,58
    • R$576,25
    • R$68,06
    • R$51,81
    • R$104,73
    • R$26,14
    • R$26,14
    • R$68,06
    • R$84,61
    • R$104,73